PFAS FAQ

PFAS questions, answered

Regulation, treatment and destruction, explained by the team that builds the systems.

THE BASICS

PFAS basics

What are PFAS?

PFAS are per- and polyfluoroalkyl substances, a large family of man-made chemicals used in firefighting foam, nonstick coatings, food packaging, textiles and many industrial processes. Their carbon-fluorine bonds are among the strongest in chemistry, so they do not break down in the environment. Read the full PFAS overview.

Where do PFAS in water come from?

Common sources are industrial sites, airports and fire training areas, landfill leachate and municipal wastewater. Treatment plants and landfills often receive PFAS they did not create, because the compounds arrive in the flows they collect.

Why are PFAS hard to treat?

The compounds resist heat, chemicals and biology, and regulators are targeting parts-per-trillion concentrations. Most treatment methods capture PFAS rather than destroy them, which leaves a concentrated waste that still has to be managed.

REGULATION

Regulation and liability

What is the federal PFAS limit in drinking water?

EPA’s April 2024 rule sets limits of 4 parts per trillion for PFOA and for PFOS, with a health goal of zero for both. Water systems must comply by April 26, 2029 unless an extension applies.

Is the compliance deadline changing?

EPA proposed in May 2026 to let eligible systems extend the PFOA and PFOS compliance date to April 26, 2031. It is a proposal, not a final rule, and systems would need to request the exemption. Systems with any result at or above 12 ppt would need to carry out interim control measures.

What happened to the limits for PFHxS, PFNA, GenX and mixtures?

EPA has proposed rescinding the limits for PFHxS, PFNA, HFPO-DA (GenX) and the hazard index mixtures and has said it may regulate them again through a different process. The proposal is not final, and several states set their own limits.

Are landfills and wastewater plants liable under CERCLA?

PFOA and PFOS are CERCLA hazardous substances, and the D.C. Circuit upheld that designation on August 18, 2026. EPA has said it does not intend to prioritize enforcement against passive receivers such as utilities and municipal landfills, but private cost recovery claims remain possible and Congress has not granted an exemption. This is not legal advice, so ask your counsel about your site.

TREATMENT

Treatment options

What are the main ways to treat PFAS in water?

Granular activated carbon, ion exchange and membranes capture PFAS from the water. Foam fractionation separates and concentrates PFAS into a small volume. Destruction technologies such as electro-oxidation break the carbon-fluorine bonds so the PFAS are eliminated rather than moved.

Why not just use carbon or ion exchange?

Both can work for the right water, but they transfer PFAS onto spent media or into a concentrate that must be regenerated, hauled and disposed of. A removal step paired with onsite destruction avoids a stream of PFAS waste leaving the site.

What is foam fractionation?

Foam fractionation uses fine bubbles to carry PFAS to the surface, where they collect as a small volume of foamate. PFAS are surface active, so they attach to the bubble surfaces. E2METRIX® Olift® foam fractionation adds ozone to the process. In a landfill leachate pilot Olift® foam fractionation reduced PFOA from 3,600 ppt to 11 ppt, a 99.7% reduction. See Olift® foam fractionation.

Does ozone make a difference?

In a second pilot at 65,000 gallons per day peak flow, air and ozone gave similar total PFAS removal, 66% and 69%. The difference showed up in the waste volume: ozone cut secondary foamate from 104 to 13 gallons per day, which is much less to destroy or haul. See the case studies.

How does electro-oxidation destroy PFAS?

Electro-oxidation passes current through electrodes to break the carbon-fluorine bonds and mineralize PFAS. E2METRIX Obreak® electro-oxidation destroyed 94 to 96% of PFAS in concentrated foamate within 24 hours in a pilot at PVSC, using under 0.016 kWh per gallon. See Obreak® electro-oxidation.

THE E2METRIX WAY

Why onsite destruction

Why destroy PFAS onsite instead of hauling the concentrate away?

Hauling moves PFAS to another site; it does not eliminate them. Treating the concentrate onsite removes transport, storage and third-party disposal from the picture and shortens the path from removal to destruction.

How do Olift® foam fractionation and Obreak® electro-oxidation work together?

Olift® foam fractionation removes PFAS from the main water stream and concentrates them into a small foamate. Obreak® electro-oxidation destroys that concentrate and the treated foamate is recycled back to the head of the process, so the loop closes without a PFAS waste stream leaving the site. See the integrated solution.

Can this treat landfill leachate and industrial wastewater?

Yes. The Olift® foam fractionation pilots were run on real landfill leachate and the Obreak® electro-oxidation pilot on wastewater concentrate at a sewerage authority. See the landfill, industrial and municipal pages for site-specific flows.

How is E2METRIX different from other PFAS treatment providers?

E2METRIX is built around removal plus onsite destruction in one closed loop, backed by pilot results on real landfill leachate and wastewater. The team is part of Ovivo, a global water treatment company, so design, supply and support sit under one roof.

How do I get started?

Send us your flow, PFAS results and site constraints. We will help you size a pilot or full-scale system and map it to your timeline. Contact the team.

RESULTS

Proven on real water

99.7%

PFOA reduction in a landfill leachate pilot

94 to 96%

PFAS destroyed in 24 hours at PVSC

13 gal/day

Secondary foamate with ozone, down from 104

0.016

kWh per gallon or less to destroy PFAS

Still have a question?

Our team answers PFAS questions every day. Ask about your site.